Volcano Classic Replacement Switch Green SR-06NR-G

$9.99

Green Replacement rocker switch fits Storz & Bickel Volcano Classic 16 A 125 VAC, 8 A 250 VAC SR-06NR

In stock

Continue Shopping

Description

Green Replacement Rocker Switch fits Volcano Classicย 

Green Replacement Volcano Classic Switch

  • Green Replacement rocker switch fits Volcano Classic.
    Note, Replacement switch top will have on off markings as pictured
  • Model SR-06NR-G-110V Illuminated rocker switch. OEM SR-06NR model switch as supplied in your unit.
  • 16 A 125 VAC, 8 A 250 VAC
  • ON – OFF 3 pins – Light 110 VOLTS
  • Fits Volcano Classic –ย this Switch is suitable for Heat or Air replacement locations.ย  Also Found in some Bissell 37603 Vacuums
  • Warranty is good for 30 days after your receipt. Please contact us if you need a replacement with in the 30 days.

Replacement Rocker Switch for your Volcano Classic. Illuminated rocker switch 16 A 125 VAC Easy Replacement at home no need to ship off your Volcano, Simply pop out your broken switch, pop in your new switch and plug in the 3 wires. You will be up and running in minutes.

Note, this item is not authorized for resale without our prior written consent. Please beware of imposters selling our wares,ย  buy your Volcano replacement switch from DepotEco.com or our sister site Volcanoswitch.com

Keep your Volcano running smoothly with this replacement part. Designed for easy installation and long-lasting performance, it ensures your device stays in top working order.
All products are intended for use with legal, nonโ€‘tobacco materials only.

See Link Below for installation.

Volcano Switch Replacement (Classic and Digit)

Volcano Switch Replacement Instructions Click To Read. You will need a Torx screwdriver tool to remove the case screws. Older Volcano units shipped with T8 Torx Screws and then began shipping with T8 Security Torx screws. Newer units also now ship with a T10 Security Torx screw.

(Please verify your screw types T8 or T10)

CSA Standards
Certified to CAN / CSA C22.2 No. 55:

This is the switch standard for Canada designed to go into other low voltage (below 600V) appliances. This receive the โ€œCSA Markโ€ or if combined with a USA approval, the โ€œcCSAus Markโ€.

Certified to ANSI / UL 1054:
This is the switch standard for the USA for UL recognized component switches designed for low voltage (below 600V) appliances.ย  This will get the โ€œCSAus markโ€ or if combined with a Canada approval, the โ€œcCSAus Markโ€.

Additional Information

Weight 0.13 lbs
Install Guide

https://depoteco.com/blog/volcano-switch/

Specs

16 A 125 VAC, 8 A 250 VAC
ON – OFF 3 pins – Light 110 VOLTS
Fits Volcano Classic – this Switch is suitable for Heat or Air replacement locations. Also Found in some Bissell 37603 Vacuums

11 reviews for Volcano Classic Replacement Switch Green SR-06NR-G

5.0 out of 5 stars (based on 11 reviews)
Excellent100%
Very good0%
Average0%
Poor0%
Terrible0%

 

November 6, 2012

By Trip. Fontaineon

November 6, 2012

This is the perfect replacement for a Volcano Vaporizer (circa 2008) rocker switch. Both my HEAT and AIR buttons went lame after about 4 years of 365 day use. They would still switch on and off, but I’d have to keep pressure to one side, and be gentle. Enough of that nonsense…

FOLLOW THESE INSTRUCTIONS

1. Use a size 8 Torx security bit to remove the screws, and remove the stainless steel cover. Be gentle. Mine had a wire attached at the back, only allowing me to remove it so far.

2. Remove the wires from the male ends of the old rocker switch. This took me quite a while, and it became clear that they didn’t want the average Joe messing with it. So I used an exact-o blade to cut the plastic housings covering the connection point. Then I was able to use needle nose pliers to remove the wires at the connection point. I kept the plastic housing to put back on after.

3. Remove old rocker switch. I just broke the plastic spring piece to get it out. You can remove it and keep it in tact, but its much more difficult and involves a lot of awkwardly placed finger pressure. Pop the old one out, but don’t throw it out yet!

4. **IMPORTANT** Remove the BLACK RUBBER RING from your old switch. The new ones (however awesome) DON’T have them, so it’s a keeper, and worth its weight in gold. Now place it on the new rocker switch. It will fit like a dream only because of this o-ring piece.

5. Make sure you have your switch facing the right direction, because you only get one shot at the next part. Pop it in, and attach the wire connections CORRECTLY!

6. Use something wet to clean all the dust from the inside of the machine, and thank your lucky stars. You just gave your Volcano Vaporizer another 4 years of life. I love you Germany. I love you for producing the BMW of Vaporizers…

Trip Fontaineon
Verified

Only logged in customers who have purchased this product may leave a review.